AUTONICS
● Counting speeds: 1 cps / 30 cps / 2 kcps / 5 kcps
● Switch between voltage input (PNP) and no-voltage input (PNP) using DIP switch
● Operation modes: count-up, count-down, count-up/down
RKC
● Heater break alarm for single phase or three phase power control
● Available for phase control, zero-cross control, relay contact, and SSR drive
● Supported CT: CV-1 (HBA-T20 / HBA-T30), CTL-6-P-N (HBA-T22 / HBA-T32)
※Two pieces of CT are used for the above.
AUTONICS
● Time configuration and control in week or year units
● Simple configuration and status monitoring
● Various functions including daylight savings time
AUTONICS
● High-speed output response
● 13 operation modes using DIP switch (PA10-U)
● Flip-flop mode for level control (PA10-U)
AUTONICS
● Ideal for starting high capacity motors
● Various time setting range and star-delta switching time
● Simple time setting, time range, and output operation configuration with analog dial and switches
AUTONICS
● Simple time setting, time range, and output operation configuration with analog dial and switches
● 6 output operations
● 16 time setting ranges
AUTONICS
● Independent ON/OFF time control
● 6 output operation modes
● 12 time setting ranges
AUTONICS
● Ideal for circuit protection and system restart in case of power failures
● Simple time configuration and status monitoring with analog dial
● Standard DIN W 48 x H 48 mm bracket included
AUTONICS
● Time configuration and control in week or year units
● Simple configuration and status monitoring
● Various functions including daylight savings time
AUTONICS
● Compact size: DIN W 48 x H 24 x L 54 mm
● Built-in lithium battery (operates without external power supply)
● Input signal types: no-voltage input, voltage input, AC/DC universal voltage input
AUTONICS
● Simple configuration and operation with analog dial
● Various time setting ranges
● Standard DIN W 48 x H 48 mm size
AUTONICS
● Wide time setting range: 0.01 s to 9999.9 h
● Switch between voltage input (PNP) and no-voltage input (PNP) using DIP switch
● Set hr/min/sec display with RESET key
RKC
● Heater break alarm for single phase or three phase power control
● Available for phase control, zero-cross control, relay contact, and SSR drive
● Supported CT: MCTL-6-P-N (load current up to 30A), MCTL-12-S56-10L-N (load current up to 100A)
※Two CTs are used for three phase control.
AUTONICS
● Time setting range: (AT8PSN: 0.05 to 10 seconds / AT8PMN: 0.05 to 10 minutes)
● Simple time configuration and status monitoring with analog dial
● Ideal for circuit protection and system restart in case of power failures
AUTONICS
● Compact, space-saving design (W 48 x H 48 x L 67 mm)
● Simple configuration with thumbwheel switches
● 10 output operation modes (LE3S)
AUTONICS
● 6 output operation modes
● 12 time setting ranges
● Wide time setting range: 0.1 s to 30 h
AUTONICS
● Ideal for starting high capacity motors
● Various time setting range and star-delta switching time
● Standard DIN W 48 x H 48 mm bracket included
AUTONICS
● Ultra-compact, miniature size (W 21.5 x H 28 x L 59.3 mm)
● 4PDT contacts (250 VAC, 3 A)
● Highly accurate timing control with analog dial
RKC
● Heater break alarm for single phase relay contact or SSR drive
● Supported CT: CV-1 (HBA-21), CTL-6-P-N (HBA-22)
RKC
Measurement accuracy: ±0.3% of displayed value Sampling time: 0.5 sec. Digital outputs:4 points (optional) Plug-in construction
Read More >